Pojačala

Sort By:  
CHAMP 2 High End and very dynamic 19" power amplifier, 2 x 350 Watts @ 4Ω, CONVECTIONAL COOLING, black Dynamic program power, both channels driven Bridge-mono operation 8 ohm : 750 W 2 channel mode 8 ohm : 200 W / ch 2 channel mode 4 ohm : 350 W / ch 2 channel mode 2.7 ohm : 450 W / ch Dynamic capacity at 2 ohm, both channels driven : 600 W / ch APart’s Champ series realizes what many in the audio industry deemed impossible: an amplifier without cooling fans that is capable of delivering high-end musical sound, high dynamics, high reliability. ŠALJEMO NA ADRESU!!!
519.00€
DCM2570 Power Amp SPEC. Bridged RMS Continuous 8Ω, (20-20k Hz, <1.0%): 2400W Both Channels RMS Continuous 4Ω (20-20k Hz, <1.0%): 8Ω (20-20k Hz, <1.0%): 1200W/1200W 700W/700W THD (20-20k Hz 50% power) 0.03% THD (20-20k Hz 90% power) 0.1% Damping Factor: >500 Slew Rate: bridged mode >50v/µs Sensitivity: (4Ω, Vms) 1.0 V Signal to Noise Ratio: Above 100dB Frequency Response: ±0.5 dB, 20 Hz to 20kHz (±1.5 dB, 10 Hz & 40 kHz) Input Impedance: >20K Ω, balanced Protection Circuits: Short Circuit • No Load Protection • SpeakerGuard™ • Thermal Shut-Off • Mute On/Off Control and Indicators: Front: Power switch • Recessed detente attenuators • Signal LED • Clip LED • Protect LED • Power Indicator Rear: Ground Lift (each channel) • Parallel Input Switch • Speaker Output Bridge Switch • Limiters IN/OUT Switch • Input Connectors: Two each; Balanced XLR & 1/4” • Speaker Output Connectors: Dual heavy duty binding posts, three Speakon™ & four 1/4” Internal Fuse SLOW BLOW - 25A, 240V/15A Dimensions: 5 1/4" High x 19" Wide x 10" Depth (3-space); 13.3 x 48.3 x 25.3 cm Net Weight: 39 lbs. (16.7Kgs) ŠALJEMO NA ADRESU!!!
899.00€
Pro 7200 8 Ohm Stereo - 590 W 4 Ohm Stereo - 1000 W 2 Ohm Stereo - 1650 W 8 Ohm Bridged - 3400 W Dramatically reduced net weight Latest generation of high speed, wide-bandwidth output devices Twin-tunnel cooling with back-to-front air flow Dual, rear-mounted, continuous variable-speed fans Balanced male and femal XLR inputs with switch-configurable XLR polarity and sensitivity selection Speakon® and five-way binding post output connectors Ground-lift switch Front panel circuit breaker switch Modular construction Model: Pro 7200 Dimensions: 19" W x 3.5" H x 12.25" D (483 mm x 89 mm x 312 mm) Weight: 21.8 lbs. (10 kg) ŠALJEMO NA ADRESU!!!
1,669.00€
XTI 4000 Specifications Output Power (1 kHz, 0.5% THD) Stereo Bridge-Mono 8 Ohm 4 Ohm 2 Ohm 8 Ohm 4 Ohm XTi 4000 650W 1200W 1600W* 2400W 3200W* *With 1% THD. Voltage Gain at 1kHz, 8 ohm rated output: XTi 4000: 34.2 dB Frequency Response: +0/-1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. Sensitivity: 1.4V Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): 100 dB (A weighted). Damping Factor: Better than 500 from 20 Hz to 400 Hz. Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz. Input Stage: Input is electronically balanced and employs precision 1% resistors. Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced. Maximum Input Signal: +22 dBu typical. AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V 50/60 Hz. AC Line Current: XTi 4000: 8.0A At Idle: Draws no more than 90 watts. Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing). DSP Section EQ: 4-band paragraphic per channel, boost/cut ±12 dB. Also adjustable high and low shelving filters. Filters: Highpass and lowpass per channel.Butterworth 6/12/18/24 dB per octave. High and low shelving filters, one per channel. Delay: For signal alignment of driver; 50 mS total delay. Subharmonic Synthesizer: Adds low-frequency content. Output Limiter: Prevents clipping. Presets: 10 user speaker presets. ŠALJEMO NA ADRESU!!!
1,255.00€
Digital Signal Processor - 2 Inputs/6 Outputs - Completely Configurable - Universal Power Supply The D.A.S. DSP-226 is a loudspeaker system management processor which uses digital signal processing in order to accomplish the functions of crossover, equalizer, limiter, and delay unit. Designed for applications such as zoning and permanent installations, PA systems and stage monitor set ups, the DSP-226 features two balanced analogue inputs, six balanced outputs using XLR connectors, RS485 in/out and USB socket on the front panel.
899.00€
1350 W x 1350 W at 4 Ω – Input Sensitivity Selector – Stereo/Bridged/Parallel Operation – speakON output connectors – Clip, protection and Signal present LED indicators The PA series amplifiers are designed and built to provide an affordable, quality powering solution. The wide range of models makes the series ideal for both installed or mobile sound reinforcement applications. The amplifiers incorporate a rugged 2 unit all-steel chassis ensuring structural rigidity. The low-noise fans offer both quiet and cool operation. The amplifier incorporates rear located switches which permit, operational mode selection (bridge, stereo or parallel) and input sensitivity selection.
1,029.00€
2100 W x 2100 W at 4 Ω – Input Sensitivity Selector – Stereo/Bridged/Parallel Operation – speakON output connectors – Clip, protection and Signal present LED indicators The PA series amplifiers are designed and built to provide an affordable, quality powering solution. The wide range of models makes the series ideal for both installed or mobile sound reinforcement applications. The amplifiers incorporate a rugged 2 unit all-steel chassis ensuring structural rigidity. The low-noise fans offer both quiet and cool operation. The amplifier incorporates rear located switches which permit, operational mode selection (bridge, stereo or parallel) and input sensitivity selection.
1,399.00€
Kratak opis Professional 3-channel amplifier with built-in active crossover and subwoofer processor. Can be used as a normal 2-channel amplifier. 1800W total power: Satellite outputs (stereo): 2x450W rms @ 4Ω; Subwoofer output (mono): 900W rms @4Ω; Very compact housing, only 2U (88mm) high. Built-in 24dB/oct. active crossover: 90-250Hz selectable crossover point; Filters on satellite outputs can be switched on/off
699.00€
JB Systems VX 700 MKII Description Professional amplifier for all-round sound reproduction Short Circuit protection DC current protection High temperature protection Forced fan cooling Bridge function Built-in limiters Balanced XLR and Jack inputs Ground/lift switch Speakon® compatible speaker outputs Binding post speaker outputs (screws) Strong Aluminum 19' front Technical Information Power stereo 4 ohm: 2x 350Wrms Power stereo 8 ohm: 2x 200Wrms Power bridge 8 ohm: 1x 700Wrms Freq. Resp. (+/-1.5dB): 10 - 50000Hz Input Sensitivity: 0,77V Input impedance: 20 kohm S/R ratio: >85dB Damping factor: >200 Slew Rate: 60V/uS Cooling: Forced Fan cooling Inputs: Balanced XLR/Jack Outputs: Speakon/binding post Power supply: AC230V / 50Hz Dimensions (mm): 88x483x260 (19"/2U) ŠALJEMO NA ADRESU!!!
258.00€
Power specifications EIA output power (1 kHz, THD 1%) Both channels 8 ohms: 450W + 450W 4 ohms: 750W + 750W 8 ohms bridged: 1.500W Electrical specifications Input sensitivity 0dB (0.775V) Input impedance 10 kohms (balanced) Frequency response 10Hz - 50kHz (-0,5dB) Voltage gain 37 dB Slew rate 22 V/ms Damping factor Higher then 400:1 @ 1kHz, 8 ohms Crosstalk -82dB (1kHz) S/N ratio -98dB Harmonic distorsion (THD) Lower then 0,1% (ref 20Hz -20kHz) Intermodulation distortion SMPTE Lower then 0,1% (SMPTE method, 60Hz & 7kHz, 400:1 ratio) General specifications Protections Power transformer thermal protection; short circuit protection; sensor for current on outputs; clip limiter on each channel; soft-start circuit (1000P to 2200P) Controls On/off switch, 21-detect input level control for each channel, Mode selector, Shield selector Indicators Power On: 1 red LED Bridge: 1 red LED Protect: 1 red LED Level: 2 x 5 LED meter Limit: 1 red LED Connections Input: 1 XLR-F + 1 1/4' jack in parallel for each channel Output: 2 binding post + 1 speakon for each channel (400-1500); 1 speakon for each channel + 1 speakon for Bridge output (1800-2200) Power supply See label on the apparatus Dimensions (W x H x D) 483 x 88 x 428 mm / 19' x 3,46' x 16,85' Weight 21 kg / 46,3 lbs ŠALJEMO NA ADRESU!!!
699.00€
CA 3600 Professional Power Amplifier The CA Series professional power amplifiers offer Martin Wisman renowned integrity and can handle exceptionally high power ratings in a compact, light weight 3RU package. The M Series amps also feature Automatic Clip Limiting to protect connected drivers; Impedance sensing to accommodate varying impedance outputs; tunnel-cooled,high efficiency heat sinks; and variable-speed DC fans to limit the operating temperature and extend amplifier life. Specifications Rated power bridge mode 8 Ohms 3600Watts @ 1 kHz at <0.5% T.H.D. Rated power (2 X4 Ohms): 1800 Watts per channel @ 1 kHz at <0.5% T.H.D. both channels driven Rated power (2 X 8 Ohms): 1200 Watts per channel @ 1 kHz at <0.5% T.H.D.both channels driven Power bandwidth: 20 Hz - 20kHz; +0, -0.5 dB at rated 500 Watts 8 Ohm power T.H.D.(2 X 4 Ohms): <0.05%@900 Watts per channel from 20 HZ to 20 kHz T.H.D.(2 X 8 Ohms): <0.05%@600Watts per channel from 20 HZ to 20 kHz Minimum load impedance: 2 Ohms Maximum RMS voltage swing: 110Volts Frequency response: 10 Hz - 50 kHz; +0, -3 dB at 1 Watt Input CMRR: >-65 dB @ 1 kHz Rated power (1 X 4 Ohms): 1980 Watts @ 1 kHz at <0.5% T.H.D. Rated power (1 X 8 Ohms): 1300 Watts @ 1 kHz at <0.5% T.H.D. Phase response: +20 to -25 from 20 Hz to 20 kHz Input impedance: 20 k Ohms, balanced; 10k Ohms, unbalanced Cooling: Tow temperature dependant variable speed 120mm high output DC fans Controls: Two front panel attenuators, rear panel mode switch and gain select switch Voltage gain: 0.775V, 32 dB or 26 dB Crosstalk: >-60 dB @ 1 kHz at rated power @ 8 Ohms Hum and noise: >-104 dB, "A" weighted referenced to rated power @ 8 Ohms Slew rate: >25V/us Damping factor (8 Ohms): >800:1 @ 20Hz - 1 kHz Indicator LEDs: 2 Clip,2 signal presence, 2 active status, 2Protection Protection: Thermal, DC, turn-on bursts, incorrect loads Connectors: XLR, Speakon and Binding Post speaker output, 240/230 Volt 20 amp IEC mains Construction: 16 ga. Steel Dimensions: 132mm x 483 mm x 498 mm Net weight: 36kg Gross weight: 39kg ŠALJEMO NA ADRESU!!!
799.00€
MA 2200 X Professional Power Amplifier Description The MA Series professional power amplifiers offer Martin Wisman renowned integrity and can handle exceptionally high power ratings in a compact, light weight 2RU package. The MA Series amps also feature Automatic Clip Limiting to protect connected drivers;Impedance sensing to accommodate varying impedance outputs; tunnel cooled,high efficiency heat sinks; and variable speed DC fans to limit the operating temperature and extend amplifier life. Individual low pass, low cut switch for channel A and B. Specifications Rated power bridge mode 4 Ohms: 2250 Watts @ 1 kHz at <0.1% T.H.D. Rated power (2 X 2 Ohms): 1125 Watts per channel @ 1 kHz at <0.1% T.H.D.both channels driven Rated power (2 X4 Ohms): 750 Watts per channel @ 1 kHz at <0.05% T.H.D. both channels driven Rated power (2 X 8 Ohms): 500 Watts per channel @ 1 kHz at <0.025% T.H.D.both channels driven Rated power (1 X 2 Ohms): 1260 Watts @ 1 kHz at <0.1% T.H.D. Power bandwidth: 10 Hz - 30kHz; +0, -3 dB at rated 350 Watts 8 Ohm power T.H.D.(2 X 2 Ohms): <0.1%@900 Watts per channel from 20 HZ to 20 kHz T.H.D.(2 X 4 Ohms): <0.1%@600 Watts per channel from 20 HZ to 20 kHz T.H.D.(2 X 8 Ohms): <0.1%@400 Watts per channel from 20 HZ to 20 kHz Minimum load impedance: 2 Ohms Maximum RMS voltage swing: 77 Volts Frequency response: 10 Hz - 100 kHz; +0, -3 dB at 1 Watt Input CMRR: >-65 dB @ 1 kHz Rated power (1 X 4 Ohms): 840 Watts @ 1 kHz at <0.05% T.H.D. Rated power (1 X 8 Ohms): 560 Watts @ 1 kHz at <0.025% T.H.D. Phase response: +5 to -15 from 20 Hz to 20 kHz Input impedance: 20 k Ohms, balanced; 10k Ohms, unbalanced Cooling: Two temperature dependant variable speed 80mm high output DC fans Controls: Two front panel attenuators, rear panel mode switch and gain select switch Voltage gain: 0.775V, 32 dB or 26 dB Crosstalk: >-60 dB @ 1 kHz at rated power @ 8 Ohms Hum and noise: >-107 dB, "A" weighted referenced to rated power @ 8 Ohms Slew rate: >30V/us Damping factor (8 Ohms): >700:1 @ 20Hz - 1 kHz Indicator LEDs: 2 Clip,2 signal presence, 1 active status,2 Protection Protection: Thermal, DC, turn-on bursts, subsonic, incorrect loads Connectors: XLR, Speakon and Binding Post speaker output, 240/230 Volt 16 amp IEC mains Construction: 16 ga. Steel Dimensions: 89 mm x 483 mm x 496 mm Net weight: 23kg Gross weight: 26 kg ŠALJEMO NA ADRESU!!!
525.00€
Kratak opis Independent Bassand Treblecontrol for each channel. Three power configerations ; four channe!4 X 200W, 3 channel 2 X 200W + 1 X 600W or 2 channel 2X600W. Individual fourchannel inputs and switchable global bus input, independent volume control for 4 channels, recessed Treble and Bass control, Independent signal indication, independent clipindication. *Bridge modeswitch forchannel 1&2 andchannel 3&4, bridge and common protection LED indicators. •Balance BUS IN available.
499.00€
Specifikacija Stereo 4 ohm: 2x 170W Stereo 8 ohm: 2x 100W Stereo 2 ohm: 2x 200W Bridge 8 ohm: 215W Bridge 4 ohm: 400W Frekvencijski odziv: 20 Hz a 20 kHz < +/- 0.5dB Distorzija: < 0.1 % (1 kHz) Ulaz izolacija: 10 - 20 kohm balansirano Signal / sum: < 95 dB Tezina: 7.5 kg Napajanje: 230V / 50Hz Dimenzije: 480 x 410 x 88 (19"/2U) ŠALJEMO NA ADRESU!!!
169.00€
ULT 1260 Professional Power Amplifier Soft start-up, preventing the transient surge and reducing the disturbance to the power network. Working mode of Stereo, Bridge and Parallel can be chosen; the sensitivity of input signal also can be chosen from 0.775V, 1.0V, 1.44V. It use high speed& low noise, speed variable fans (the speed goes up along with the temperature increases); Limiter protection, overheat protection, over-current protection, DC protection and short circuit protection. COMBO & XLR Link male input; SPEAKON and binding post output connectors. Stereo 8Ω Power 420W x2 Stereo 4Ω Power 630W x2 Bridge 8Ω Power 1260W THD+N ≤0.5% IMD <0.3% Frequency response 20Hz ~ 20kHz ± 1.5dB Input Sensitivity 0.775V/1.0V/1.44V (stereo 8Ω) S/N ratio >100dB Crosstalk >70dB Phase Response ± 10 degrees Damping Factor >200 (@8Ω) Protection Soft start up, thermal cut off, short circuit, overloaded, DC fault, Voltage limiter and AC line fuse Connectors Input: COMBO x 2, XLR Link male x 2; Output: SPEAKON x 2; Binding Post x 2 Power supply 230V ± 10% ~50/60Hz Dimension 483 x 345 x 88mm (19", 2U) Weight 18.5kgs ŠALJEMO NA ADRESU!!!
288.00€
BROJ 1 U AMERICI, DALEKO ISPRED SVIH !!! 2 x 2500 W NA 2 OHM !!! RMX 5050 SPECIFICATIONS RMX 5050 STEREO MODE, Both Channels Driven 8 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 1050 W 1100 W 4 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 1600 W 1800 W 2 ohms FTC 20 Hz-20 kHz 0.1% THD EIA 1 kHz 1% THD 2000 W 2500 W BRIDGE-MONO MODE 8 ohms FTC 20 Hz-20 kHz 0.1% THD EIA 1 kHz 0.1% THD 3200 W 3600 W 4 ohms EIA 1 kHz 1% THD 5000 W Distortion (SMPTE-IM) Less than 0.02% Distortion (Typical) 20 Hz - 20 kHz: 10 dB below rated power 1 kHz and below: full rated power Less than 0.02% Less than 0.02% Frequency Response 20 Hz - 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB 5 Hz - 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB Damping Factor Greater than 250 @ 8 ohm Noise (unweighted) 100 dB below rated output (20 Hz - 20 kHz, 8 ohm load) Input Sensitivity 1.42 Vrms for 1050 watts into 8 ohms Voltage Gain 64x (36 dB) for 8 ohm load Input Impedance 20k ohm balanced, 10k ohm unbalanced Controls Front: Controls Rear: AC power switch, Ch. 1 and Ch. 2 gain control 10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel. Indicators Power-On: Green LED, Protect: Red LED Signal -30dB: Yellow LED, Clip: Red LED Connectors Input: Connectors Output: XLR female, TRS (1/4\"), and barrier-strip screw terminals, each channel Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp) Cooling Continuously variable-speed fan, rear-to-front air flow Amplifier Protection Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads Load Protection On/off muting, DC fault output crowbar Power Requirements 100, 120 or 240 Volts AC (±10%) 50-60 Hz (factory configured) 120V models require 20 Amp service and are supplied with a NEMA 5-20 plug on the cordset. Dimensions 19\" (48.3 cm) wide, 5.25\" (13.3 cm) tall, 15.9\" (40.39 cm) overall depth Weight 75 lbs (34.02 kg) net, 87 lbs (39.46 kg) shipping ŠALJEMO NA ADRESU!!!
1,867.00€
APart CHAMP 2 (CHAMP 2)
CHAMP 2
 

High End and very dynamic 19" power amplifier, 2 x 350 Watts @ 4Ω, CONVECTIONAL COOLING, black
 
Dynamic program power, both channels driven
Bridge-mono operation 8 ohm : 750 W
2 channel mode 8 ohm : 200 W / ch
2 channel mode 4 ohm : 350 W / ch
2 channel mode 2.7 ohm : 450 W / ch
Dynamic capacity at 2 ohm, both channels driven : 600 W / ch

APart’s Champ series realizes what many in the audio industry deemed impossible: an amplifier without cooling fans that is capable of delivering high-end musical sound, high dynamics, high reliability.


ŠALJEMO NA ADRESU!!!
CHAMP 2 High End and very dynamic 19" power amplifier, 2 x 350 Watts @ 4Ω, CONVECTIONAL COOLING, black Dynamic program power, both channels driven Bridge-mono operation 8 ohm : 750 W 2 channel mode 8 ohm : 200 W / ch 2 channel mode 4 ohm : 350 W / ch 2 channel mode 2.7 ohm : 450 W / ch Dynamic capacity at 2 ohm, both channels driven : 600 W / ch APart’s Champ series realizes what many in the audio industry deemed impossible: an amplifier without cooling fans that is capable of delivering high-end musical sound, high dynamics, high reliability. ŠALJEMO NA ADRESU!!!
519.00€
Carvin DCM 2570 (DCM 2570)
DCM2570 Power Amp SPEC.
 
Bridged RMS Continuous
8Ω, (20-20k Hz, <1.0%):
 2400W
Both Channels RMS Continuous
4Ω (20-20k Hz, <1.0%):
8Ω (20-20k Hz, <1.0%):
 
1200W/1200W
700W/700W
THD (20-20k Hz 50% power)     0.03%
THD (20-20k Hz 90% power)     0.1%
Damping Factor:     >500
Slew Rate:    bridged mode  >50v/µs
Sensitivity:    (4Ω, Vms) 1.0 V
Signal to Noise Ratio:     Above 100dB
Frequency Response:     ±0.5 dB, 20 Hz to 20kHz
(±1.5 dB, 10 Hz & 40 kHz)
Input Impedance:    >20K Ω, balanced
Protection Circuits:     Short Circuit • No Load Protection • SpeakerGuard™ • Thermal Shut-Off • Mute On/Off
Control and Indicators:    Front: Power switch • Recessed detente attenuators • Signal LED • Clip LED • Protect LED • Power Indicator
Rear: Ground Lift (each channel) • Parallel Input Switch • Speaker Output Bridge Switch • Limiters 
IN/OUT Switch • Input Connectors: Two each; Balanced XLR & 1/4” • Speaker Output Connectors:
Dual heavy duty binding posts, three Speakon™ & four 1/4”
Internal Fuse SLOW BLOW    - 25A, 240V/15A
Dimensions:    5 1/4" High x 19" Wide x 10" Depth (3-space); 13.3 x 48.3 x 25.3 cm
Net Weight:    39 lbs. (16.7Kgs)

ŠALJEMO NA ADRESU!!!
DCM2570 Power Amp SPEC. Bridged RMS Continuous 8Ω, (20-20k Hz, <1.0%): 2400W Both Channels RMS Continuous 4Ω (20-20k Hz, <1.0%): 8Ω (20-20k Hz, <1.0%): 1200W/1200W 700W/700W THD (20-20k Hz 50% power) 0.03% THD (20-20k Hz 90% power) 0.1% Damping Factor: >500 Slew Rate: bridged mode >50v/µs Sensitivity: (4Ω, Vms) 1.0 V Signal to Noise Ratio: Above 100dB Frequency Response: ±0.5 dB, 20 Hz to 20kHz (±1.5 dB, 10 Hz & 40 kHz) Input Impedance: >20K Ω, balanced Protection Circuits: Short Circuit • No Load Protection • SpeakerGuard™ • Thermal Shut-Off • Mute On/Off Control and Indicators: Front: Power switch • Recessed detente attenuators • Signal LED • Clip LED • Protect LED • Power Indicator Rear: Ground Lift (each channel) • Parallel Input Switch • Speaker Output Bridge Switch • Limiters IN/OUT Switch • Input Connectors: Two each; Balanced XLR & 1/4” • Speaker Output Connectors: Dual heavy duty binding posts, three Speakon™ & four 1/4” Internal Fuse SLOW BLOW - 25A, 240V/15A Dimensions: 5 1/4" High x 19" Wide x 10" Depth (3-space); 13.3 x 48.3 x 25.3 cm Net Weight: 39 lbs. (16.7Kgs) ŠALJEMO NA ADRESU!!!
899.00€
CREST AUDIO Pro 7200 (Pro 7200)
Pro 7200
 
8 Ohm Stereo - 590 W
4 Ohm Stereo - 1000 W
2 Ohm Stereo - 1650 W
8 Ohm Bridged - 3400 W
Dramatically reduced net weight
Latest generation of high speed, wide-bandwidth output devices
Twin-tunnel cooling with back-to-front air flow
Dual, rear-mounted, continuous variable-speed fans
Balanced male and femal XLR inputs with switch-configurable XLR polarity and sensitivity selection
Speakon® and five-way binding post output connectors
Ground-lift switch
Front panel circuit breaker switch
Modular construction
 
Model:    Pro 7200
Dimensions:    19" W x 3.5" H x 12.25" D
(483 mm x 89 mm x 312 mm)
Weight:    21.8 lbs. (10 kg)

ŠALJEMO NA ADRESU!!!
Pro 7200 8 Ohm Stereo - 590 W 4 Ohm Stereo - 1000 W 2 Ohm Stereo - 1650 W 8 Ohm Bridged - 3400 W Dramatically reduced net weight Latest generation of high speed, wide-bandwidth output devices Twin-tunnel cooling with back-to-front air flow Dual, rear-mounted, continuous variable-speed fans Balanced male and femal XLR inputs with switch-configurable XLR polarity and sensitivity selection Speakon® and five-way binding post output connectors Ground-lift switch Front panel circuit breaker switch Modular construction Model: Pro 7200 Dimensions: 19" W x 3.5" H x 12.25" D (483 mm x 89 mm x 312 mm) Weight: 21.8 lbs. (10 kg) ŠALJEMO NA ADRESU!!!
1,669.00€
CROWN XTI 4000 (XTI 4000)
XTI 4000
 
Specifications
 
Output Power (1 kHz, 0.5% THD)
     Stereo    Bridge-Mono
8 Ohm    4 Ohm    2 Ohm    8 Ohm    4 Ohm
XTi 4000    650W    1200W    1600W*    2400W    3200W*
*With 1% THD.
Voltage Gain at 1kHz, 8 ohm rated output:
XTi 4000: 34.2 dB
Frequency Response: +0/-1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity: 1.4V
Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): 
100 dB (A weighted).
Damping Factor: Better than 500 from 20 Hz to 400 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V 
50/60 Hz.
AC Line Current:
XTi 4000: 8.0A
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
DSP Section

EQ: 4-band paragraphic per channel, boost/cut ±12 dB.
Also adjustable high and low shelving filters.
Filters: Highpass and lowpass per channel.Butterworth
6/12/18/24 dB per octave. High and low shelving filters, one per channel.
Delay: For signal alignment of driver; 50 mS total delay.
Subharmonic Synthesizer: Adds low-frequency content.
Output Limiter: Prevents clipping.
Presets: 10 user speaker presets.

ŠALJEMO NA ADRESU!!!
XTI 4000 Specifications Output Power (1 kHz, 0.5% THD) Stereo Bridge-Mono 8 Ohm 4 Ohm 2 Ohm 8 Ohm 4 Ohm XTi 4000 650W 1200W 1600W* 2400W 3200W* *With 1% THD. Voltage Gain at 1kHz, 8 ohm rated output: XTi 4000: 34.2 dB Frequency Response: +0/-1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms. Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo mode, 4 to 16 ohms in Bridge-Mono mode. Sensitivity: 1.4V Signal to Noise Ratio (below rated 1 kHz power at 8 ohms): 100 dB (A weighted). Damping Factor: Better than 500 from 20 Hz to 400 Hz. Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz. Input Stage: Input is electronically balanced and employs precision 1% resistors. Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced. Maximum Input Signal: +22 dBu typical. AC Line Voltage and Frequency Configurations Available: 100V, 120V, 220-240V 50/60 Hz. AC Line Current: XTi 4000: 8.0A At Idle: Draws no more than 90 watts. Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing). DSP Section EQ: 4-band paragraphic per channel, boost/cut ±12 dB. Also adjustable high and low shelving filters. Filters: Highpass and lowpass per channel.Butterworth 6/12/18/24 dB per octave. High and low shelving filters, one per channel. Delay: For signal alignment of driver; 50 mS total delay. Subharmonic Synthesizer: Adds low-frequency content. Output Limiter: Prevents clipping. Presets: 10 user speaker presets. ŠALJEMO NA ADRESU!!!
1,255.00€
DAS AUDIO DSP-226 (DSP-226)
Frequency Response20 Hz-20 kHz, +0/-0.5 dBDynamic Range116 dB A WeightingChannel Separation< -100 dBDistortion (THD)0.003%, 1kHz at 0 dBuInput Metering-24 dB,-12 dB,-6 dB, 0 dB+6 dB,+12 dB,+24 dBOutput Metering-24 dB,-12 dB,-6 dB, 0 dB+6 dB,+12 dB,+24 dBAC Requirements95-240 VAC 50/60 HzDimensions (H x W x D)4.5 x 48.2 x 15.8 cm1.77 x 19 x 6.2 inWeight2 kg (4.4 lb)
Digital Signal Processor - 2 Inputs/6 Outputs - Completely Configurable - Universal Power Supply The D.A.S. DSP-226 is a loudspeaker system management processor which uses digital signal processing in order to accomplish the functions of crossover, equalizer, limiter, and delay unit. Designed for applications such as zoning and permanent installations, PA systems and stage monitor set ups, the DSP-226 features two balanced analogue inputs, six balanced outputs using XLR connectors, RS485 in/out and USB socket on the front panel.
899.00€
DAS AUDIO PA-2700 (PA-2700)
Stereo Mode (both channels driven)8 ohms EIA 1 kHz 1% THD1000 W4 ohms EIA 1 kHz 1% THD1350 WBridge Mono Mode8 ohms EIA 1 kHz 1% THD2700 WFrequency Response20 Hz-20 kHz +0-1 dBSignal to Noise Ratio (20 Hz-20 kHz)> 100 dBDistortion (SMPTE-IM)≤ 0.35%Total Harmonic Distortion (20 Hz-20 kHz)≤ 0.35%Damping Factor @ 8 ohms> 200Input Sensitivity @ 4 ohms0.775 V o 1.4 VVoltage Gain36 dBAC Requirements230 V AC 50 HzCurrent Draw (1/3 power @ 230 V)9.2 ADimensions (H x W x D)8.8 x 48.2 x 29.4 cm 3.5 x 19 x 11.6 inWeight19.5 kg 43 lb
1350 W x 1350 W at 4 Ω – Input Sensitivity Selector – Stereo/Bridged/Parallel Operation – speakON output connectors – Clip, protection and Signal present LED indicators The PA series amplifiers are designed and built to provide an affordable, quality powering solution. The wide range of models makes the series ideal for both installed or mobile sound reinforcement applications. The amplifiers incorporate a rugged 2 unit all-steel chassis ensuring structural rigidity. The low-noise fans offer both quiet and cool operation. The amplifier incorporates rear located switches which permit, operational mode selection (bridge, stereo or parallel) and input sensitivity selection.
1,029.00€
DAS AUDIO PA-4000 (PA-4000)
Stereo Mode (both channels driven)8 ohms EIA 1 kHz 1% THD1400 W4 ohms EIA 1 kHz 1% THD2100 WBridge Mono Mode8 ohms EIA 1 kHz 1% THD4200 WFrequency Response20 Hz-20 kHz +0-1 dBSignal to Noise Ratio (20 Hz-20 kHz)> 100 dBDistortion (SMPTE-IM)≤ 0.35%Total Harmonic Distortion (20 Hz-20 kHz)<0.5%Damping Factor @ 8 ohms> 200Input Sensitivity @ 4 ohms0.775 V o 1.4 V0Voltage Gain37 dBAC Requirements230 V AC 50 HzCurrent Draw (1/3 power @ 230 V)15.2 ADimensions (H x W x D)8.8 x 48.2 x 29.4 cm 3.5 x 19 x 11.6 inWeight19.5 kg 43 lb

2100 W x 2100 W at 4 Ω – Input Sensitivity Selector – Stereo/Bridged/Parallel Operation – speakON output connectors – Clip, protection and Signal present LED indicators The PA series amplifiers are designed and built to provide an affordable, quality powering solution. The wide range of models makes the series ideal for both installed or mobile sound reinforcement applications. The amplifiers incorporate a rugged 2 unit all-steel chassis ensuring structural rigidity. The low-noise fans offer both quiet and cool operation. The amplifier incorporates rear located switches which permit, operational mode selection (bridge, stereo or parallel) and input sensitivity selection.
1,399.00€
JBSystems C3 1800 (C3 1800)

Professional 3-channel amplifier with built-in active crossover and subwoofer processor


Can be used as a normal 2-channel amplifier.

  • 1800W total power:
  • Satellite outputs (stereo): 2x450W rms @ 4Ω 
  • Subwoofer output (mono): 900W rms @4Ω 

 

  • Very compact housing, only 2U (88mm) high
  • Built-in 24dB/oct. active crossover:
  • 90-250Hz selectable crossover point
  • Filters on satellite outputs can be switched on/off
  • Built-in SUB BASS processor
  • Limiters can be switched on/off
  • Sub out phase inverter
  • Soft starts
  • Very efficient cooling 
  • DC fault protection
  • High temperature protection
  • Overload and short circuit protections
  • Balanced inputs with XLR connectors 
  • 3 Speakon® outputs: 2x Satellites + 1x Sub out.

 

Technical information:

 

Power Satellite outputs @ 4Ω:

 2x 450Wrms

Power Satellite outputs @ 8Ω:  2x 300Wrms
Power Subwoofer outputs @ 4Ω:  1x 900Wrms
Power Subwoofer outputs @ 8Ω:  1x 600Wrms
Freq. Resp. (+/-0.5dB):  20 - 20000Hz 
Active crossover:  90-250Hz (24dB/oct. Linkwitz Riley)
Input Sensitivity:  770mV 
Input impedance:  20 kΩ (bal) / 10kΩ (unbal)
S/R ratio:  >90dB
Damping factor:  >500
Cooling:  dual speed fan cooling
Inputs:  balanced XLR
Outputs:  Speakon®
Power supply:  AC230V / 50Hz
Dimensions (mm):  483x473x88 (19"/2U)
Weight:  24kg

ŠALJEMO NA ADRESU!!!

 

Kratak opis Professional 3-channel amplifier with built-in active crossover and subwoofer processor. Can be used as a normal 2-channel amplifier. 1800W total power: Satellite outputs (stereo): 2x450W rms @ 4Ω; Subwoofer output (mono): 900W rms @4Ω; Very compact housing, only 2U (88mm) high. Built-in 24dB/oct. active crossover: 90-250Hz selectable crossover point; Filters on satellite outputs can be switched on/off
699.00€
JBSystems VX 700 MKII (VX 700 MKII)
JB Systems VX 700 MKII
 
Description 

Professional amplifier for all-round sound reproduction
Short Circuit protection
DC current protection
High temperature protection
Forced fan cooling
Bridge function
Built-in limiters
Balanced XLR and Jack inputs
Ground/lift switch
Speakon® compatible speaker outputs
Binding post speaker outputs (screws)
Strong Aluminum 19' front

Technical Information

Power stereo 4 ohm:    2x 350Wrms
Power stereo 8 ohm:    2x 200Wrms
Power bridge 8 ohm:    1x 700Wrms
Freq. Resp. (+/-1.5dB):    10 - 50000Hz
Input Sensitivity:    0,77V
Input impedance:    20 kohm
S/R ratio:    >85dB
Damping factor:    >200
Slew Rate:    60V/uS
Cooling:    Forced Fan cooling
Inputs:    Balanced XLR/Jack
Outputs:    Speakon/binding post
Power supply:    AC230V / 50Hz
Dimensions (mm):    88x483x260 (19"/2U)

ŠALJEMO NA ADRESU!!!
JB Systems VX 700 MKII Description Professional amplifier for all-round sound reproduction Short Circuit protection DC current protection High temperature protection Forced fan cooling Bridge function Built-in limiters Balanced XLR and Jack inputs Ground/lift switch Speakon® compatible speaker outputs Binding post speaker outputs (screws) Strong Aluminum 19' front Technical Information Power stereo 4 ohm: 2x 350Wrms Power stereo 8 ohm: 2x 200Wrms Power bridge 8 ohm: 1x 700Wrms Freq. Resp. (+/-1.5dB): 10 - 50000Hz Input Sensitivity: 0,77V Input impedance: 20 kohm S/R ratio: >85dB Damping factor: >200 Slew Rate: 60V/uS Cooling: Forced Fan cooling Inputs: Balanced XLR/Jack Outputs: Speakon/binding post Power supply: AC230V / 50Hz Dimensions (mm): 88x483x260 (19"/2U) ŠALJEMO NA ADRESU!!!
258.00€
LEM Procon 1500 plus (Procon 1500 plus)
Power specifications     
EIA output power
(1 kHz, THD 1%) Both channels    8 ohms: 450W + 450W
4 ohms: 750W + 750W
8 ohms bridged: 1.500W
Electrical specifications     
Input sensitivity    0dB (0.775V)
Input impedance    10 kohms (balanced)
Frequency response    10Hz - 50kHz (-0,5dB)
Voltage gain    37 dB
Slew rate    22 V/ms
Damping factor    Higher then 400:1 @ 1kHz, 8 ohms
Crosstalk    -82dB (1kHz)
S/N ratio    -98dB
Harmonic distorsion
(THD)    Lower then 0,1% (ref 20Hz -20kHz)
Intermodulation distortion
SMPTE    Lower then 0,1% (SMPTE method, 60Hz & 7kHz, 400:1 ratio)
General specifications     
Protections    Power transformer thermal protection; short circuit protection; sensor for current on outputs; clip limiter on each channel; soft-start circuit (1000P to 2200P)
Controls    On/off switch, 21-detect input level control for each channel, Mode selector, Shield selector
Indicators    Power On: 1 red LED
Bridge: 1 red LED
Protect: 1 red LED
Level: 2 x 5 LED meter
Limit: 1 red LED
Connections    Input: 1 XLR-F + 1 1/4' jack in parallel for each channel
Output: 2 binding post + 1 speakon for each channel (400-1500); 1 speakon for each channel + 1 speakon for Bridge output (1800-2200)
Power supply    See label on the apparatus
Dimensions
(W x H x D)    483 x 88 x 428 mm /
19' x 3,46' x 16,85'
Weight    21 kg / 46,3 lbs

ŠALJEMO NA ADRESU!!!
Power specifications EIA output power (1 kHz, THD 1%) Both channels 8 ohms: 450W + 450W 4 ohms: 750W + 750W 8 ohms bridged: 1.500W Electrical specifications Input sensitivity 0dB (0.775V) Input impedance 10 kohms (balanced) Frequency response 10Hz - 50kHz (-0,5dB) Voltage gain 37 dB Slew rate 22 V/ms Damping factor Higher then 400:1 @ 1kHz, 8 ohms Crosstalk -82dB (1kHz) S/N ratio -98dB Harmonic distorsion (THD) Lower then 0,1% (ref 20Hz -20kHz) Intermodulation distortion SMPTE Lower then 0,1% (SMPTE method, 60Hz & 7kHz, 400:1 ratio) General specifications Protections Power transformer thermal protection; short circuit protection; sensor for current on outputs; clip limiter on each channel; soft-start circuit (1000P to 2200P) Controls On/off switch, 21-detect input level control for each channel, Mode selector, Shield selector Indicators Power On: 1 red LED Bridge: 1 red LED Protect: 1 red LED Level: 2 x 5 LED meter Limit: 1 red LED Connections Input: 1 XLR-F + 1 1/4' jack in parallel for each channel Output: 2 binding post + 1 speakon for each channel (400-1500); 1 speakon for each channel + 1 speakon for Bridge output (1800-2200) Power supply See label on the apparatus Dimensions (W x H x D) 483 x 88 x 428 mm / 19' x 3,46' x 16,85' Weight 21 kg / 46,3 lbs ŠALJEMO NA ADRESU!!!
699.00€
Martin Wisman CA 3600 (CA 3600)
CA 3600
 
Professional Power Amplifier


The CA Series professional power amplifiers offer Martin Wisman renowned integrity and can handle exceptionally high power ratings in a compact, light weight 3RU package. The M Series amps also feature Automatic Clip Limiting to protect connected drivers; Impedance sensing to accommodate varying impedance outputs; tunnel-cooled,high efficiency heat sinks; and variable-speed DC fans to limit the operating temperature and extend amplifier life.

Specifications
 
Rated power bridge mode 8 Ohms
3600Watts @ 1 kHz at <0.5% T.H.D.
Rated power (2 X4 Ohms):
1800 Watts per channel @ 1 kHz at <0.5%
T.H.D. both channels driven
Rated power (2 X 8 Ohms):
1200 Watts per channel @ 1 kHz at <0.5%
T.H.D.both channels driven
Power bandwidth:
20 Hz - 20kHz; +0, -0.5 dB at rated 500 Watts 8 Ohm power
T.H.D.(2 X 4 Ohms):
<0.05%@900 Watts per channel from 20 HZ to 20 kHz
T.H.D.(2 X 8 Ohms):
<0.05%@600Watts per channel from 20 HZ to 20 kHz
Minimum load impedance:
2 Ohms
Maximum RMS voltage swing:
110Volts
Frequency response:
10 Hz - 50 kHz; +0, -3 dB at 1 Watt
Input CMRR:
>-65 dB @ 1 kHz
Rated power (1 X 4 Ohms):
1980 Watts @ 1 kHz at <0.5% T.H.D.
Rated power (1 X 8 Ohms):
1300 Watts @ 1 kHz at <0.5% T.H.D.
Phase response:
+20 to -25 from 20 Hz to 20 kHz
Input impedance:
20 k Ohms, balanced; 10k Ohms, unbalanced
Cooling:
Tow temperature dependant variable speed 120mm high output DC fans
Controls:
Two front panel attenuators, rear panel mode switch and gain select switch
Voltage gain:
0.775V, 32 dB or 26 dB
Crosstalk:
>-60 dB @ 1 kHz at rated power @ 8 Ohms
Hum and noise:
>-104 dB, "A" weighted referenced to rated power @ 8 Ohms
Slew rate:
>25V/us
Damping factor (8 Ohms):
>800:1 @ 20Hz - 1 kHz
Indicator LEDs:
2 Clip,2 signal presence, 2 active status, 2Protection
Protection:
Thermal, DC, turn-on bursts, incorrect loads
Connectors:
XLR, Speakon and Binding Post speaker output,
240/230 Volt 20 amp IEC mains
Construction:
16 ga. Steel
Dimensions:
132mm x 483 mm x 498 mm
Net weight:
36kg
Gross weight:
39kg

ŠALJEMO NA ADRESU!!!
CA 3600 Professional Power Amplifier The CA Series professional power amplifiers offer Martin Wisman renowned integrity and can handle exceptionally high power ratings in a compact, light weight 3RU package. The M Series amps also feature Automatic Clip Limiting to protect connected drivers; Impedance sensing to accommodate varying impedance outputs; tunnel-cooled,high efficiency heat sinks; and variable-speed DC fans to limit the operating temperature and extend amplifier life. Specifications Rated power bridge mode 8 Ohms 3600Watts @ 1 kHz at <0.5% T.H.D. Rated power (2 X4 Ohms): 1800 Watts per channel @ 1 kHz at <0.5% T.H.D. both channels driven Rated power (2 X 8 Ohms): 1200 Watts per channel @ 1 kHz at <0.5% T.H.D.both channels driven Power bandwidth: 20 Hz - 20kHz; +0, -0.5 dB at rated 500 Watts 8 Ohm power T.H.D.(2 X 4 Ohms): <0.05%@900 Watts per channel from 20 HZ to 20 kHz T.H.D.(2 X 8 Ohms): <0.05%@600Watts per channel from 20 HZ to 20 kHz Minimum load impedance: 2 Ohms Maximum RMS voltage swing: 110Volts Frequency response: 10 Hz - 50 kHz; +0, -3 dB at 1 Watt Input CMRR: >-65 dB @ 1 kHz Rated power (1 X 4 Ohms): 1980 Watts @ 1 kHz at <0.5% T.H.D. Rated power (1 X 8 Ohms): 1300 Watts @ 1 kHz at <0.5% T.H.D. Phase response: +20 to -25 from 20 Hz to 20 kHz Input impedance: 20 k Ohms, balanced; 10k Ohms, unbalanced Cooling: Tow temperature dependant variable speed 120mm high output DC fans Controls: Two front panel attenuators, rear panel mode switch and gain select switch Voltage gain: 0.775V, 32 dB or 26 dB Crosstalk: >-60 dB @ 1 kHz at rated power @ 8 Ohms Hum and noise: >-104 dB, "A" weighted referenced to rated power @ 8 Ohms Slew rate: >25V/us Damping factor (8 Ohms): >800:1 @ 20Hz - 1 kHz Indicator LEDs: 2 Clip,2 signal presence, 2 active status, 2Protection Protection: Thermal, DC, turn-on bursts, incorrect loads Connectors: XLR, Speakon and Binding Post speaker output, 240/230 Volt 20 amp IEC mains Construction: 16 ga. Steel Dimensions: 132mm x 483 mm x 498 mm Net weight: 36kg Gross weight: 39kg ŠALJEMO NA ADRESU!!!
799.00€
Martin Wisman MA 2200 X (MA 2200 X)
MA 2200 X Professional Power Amplifier

Description

The MA Series professional power amplifiers offer Martin Wisman renowned integrity and can handle exceptionally high power ratings in a compact, light weight 2RU package. The MA Series amps also feature Automatic Clip Limiting to protect connected drivers;Impedance sensing to accommodate varying impedance outputs; tunnel cooled,high efficiency heat sinks; and variable speed DC fans to limit the operating temperature and extend amplifier life. Individual low pass, low cut switch for channel A and B. 

Specifications

Rated power bridge mode 4 Ohms:    2250 Watts @ 1 kHz at <0.1% T.H.D.
Rated power (2 X 2 Ohms):    1125 Watts per channel @ 1 kHz at <0.1%
T.H.D.both channels driven
Rated power (2 X4 Ohms):    750 Watts per channel @ 1 kHz at <0.05% 
T.H.D. both channels driven
Rated power (2 X 8 Ohms):    500 Watts per channel @ 1 kHz at <0.025%
T.H.D.both channels driven
Rated power (1 X 2 Ohms):    1260 Watts @ 1 kHz at <0.1% T.H.D.
Power bandwidth:    10 Hz - 30kHz; +0, -3 dB at rated 350 Watts 8 Ohm power
T.H.D.(2 X 2 Ohms):    <0.1%@900 Watts per channel from 20 HZ to 20 kHz
T.H.D.(2 X 4 Ohms):    <0.1%@600 Watts per channel from 20 HZ to 20 kHz
T.H.D.(2 X 8 Ohms):    <0.1%@400 Watts per channel from 20 HZ to 20 kHz
Minimum load impedance:    2 Ohms
Maximum RMS voltage swing:    77 Volts
Frequency response:    10 Hz - 100 kHz; +0, -3 dB at 1 Watt
Input CMRR:    >-65 dB @ 1 kHz
Rated power (1 X 4 Ohms):    840 Watts @ 1 kHz at <0.05% T.H.D.
Rated power (1 X 8 Ohms):    560 Watts @ 1 kHz at <0.025% T.H.D.
Phase response:    +5 to -15 from 20 Hz to 20 kHz
Input impedance:    20 k Ohms, balanced; 10k Ohms, unbalanced
Cooling:    Two temperature dependant variable speed 80mm high output DC fans
Controls:    Two front panel attenuators, rear panel mode switch and gain select switch
Voltage gain:    0.775V, 32 dB or 26 dB
Crosstalk:    >-60 dB @ 1 kHz at rated power @ 8 Ohms
Hum and noise:    >-107 dB, "A" weighted referenced to rated power @ 8 Ohms
Slew rate:    >30V/us
Damping factor (8 Ohms):    >700:1 @ 20Hz - 1 kHz
Indicator LEDs:    2 Clip,2 signal presence, 1 active status,2 Protection
Protection:    Thermal, DC, turn-on bursts, subsonic, incorrect loads
Connectors:    XLR, Speakon and Binding Post speaker output, 240/230 Volt 16 amp IEC mains
Construction:    16 ga. Steel
Dimensions:    89 mm x 483 mm x 496 mm
Net weight:    23kg
Gross weight:    26 kg

ŠALJEMO NA ADRESU!!!
MA 2200 X Professional Power Amplifier Description The MA Series professional power amplifiers offer Martin Wisman renowned integrity and can handle exceptionally high power ratings in a compact, light weight 2RU package. The MA Series amps also feature Automatic Clip Limiting to protect connected drivers;Impedance sensing to accommodate varying impedance outputs; tunnel cooled,high efficiency heat sinks; and variable speed DC fans to limit the operating temperature and extend amplifier life. Individual low pass, low cut switch for channel A and B. Specifications Rated power bridge mode 4 Ohms: 2250 Watts @ 1 kHz at <0.1% T.H.D. Rated power (2 X 2 Ohms): 1125 Watts per channel @ 1 kHz at <0.1% T.H.D.both channels driven Rated power (2 X4 Ohms): 750 Watts per channel @ 1 kHz at <0.05% T.H.D. both channels driven Rated power (2 X 8 Ohms): 500 Watts per channel @ 1 kHz at <0.025% T.H.D.both channels driven Rated power (1 X 2 Ohms): 1260 Watts @ 1 kHz at <0.1% T.H.D. Power bandwidth: 10 Hz - 30kHz; +0, -3 dB at rated 350 Watts 8 Ohm power T.H.D.(2 X 2 Ohms): <0.1%@900 Watts per channel from 20 HZ to 20 kHz T.H.D.(2 X 4 Ohms): <0.1%@600 Watts per channel from 20 HZ to 20 kHz T.H.D.(2 X 8 Ohms): <0.1%@400 Watts per channel from 20 HZ to 20 kHz Minimum load impedance: 2 Ohms Maximum RMS voltage swing: 77 Volts Frequency response: 10 Hz - 100 kHz; +0, -3 dB at 1 Watt Input CMRR: >-65 dB @ 1 kHz Rated power (1 X 4 Ohms): 840 Watts @ 1 kHz at <0.05% T.H.D. Rated power (1 X 8 Ohms): 560 Watts @ 1 kHz at <0.025% T.H.D. Phase response: +5 to -15 from 20 Hz to 20 kHz Input impedance: 20 k Ohms, balanced; 10k Ohms, unbalanced Cooling: Two temperature dependant variable speed 80mm high output DC fans Controls: Two front panel attenuators, rear panel mode switch and gain select switch Voltage gain: 0.775V, 32 dB or 26 dB Crosstalk: >-60 dB @ 1 kHz at rated power @ 8 Ohms Hum and noise: >-107 dB, "A" weighted referenced to rated power @ 8 Ohms Slew rate: >30V/us Damping factor (8 Ohms): >700:1 @ 20Hz - 1 kHz Indicator LEDs: 2 Clip,2 signal presence, 1 active status,2 Protection Protection: Thermal, DC, turn-on bursts, subsonic, incorrect loads Connectors: XLR, Speakon and Binding Post speaker output, 240/230 Volt 16 amp IEC mains Construction: 16 ga. Steel Dimensions: 89 mm x 483 mm x 496 mm Net weight: 23kg Gross weight: 26 kg ŠALJEMO NA ADRESU!!!
525.00€
Martin Wisman UL Q1200 (UL Q1200)

UL-Q 1200



4-Channel Power Amplifier

  • Independent Bassand Treblecontrol for each channel.
  • Three power configerations ; four channe!4 X 200W, 3 channel 2 X 200W + 1 X 600W
  • or 2 channel 2X600W.
  • Individual fourchannel inputs and switchable global bus input, independent volume control for 4 channels, recessed Treble and Bass control,
  • Independent signal indication, independent clipindication. *Bridge modeswitch forchannel 1&2 andchannel 3&4, bridge and common protection
  • LED indicators. •Balance BUS IN available.
  • 8 Ohm stereo  4X200W
  • 4 Ohm stereo  4X300W
  • 8 Ohms bridged  2X600W
  • Weight 16kg



Minimum Guaranteed Power

 

  • 1 kHz with 0.5%THD
  • 4-Channel, 8 ohms     4X200W
  • 4-Channel, 4 ohms      4X300W
  • Bridge -stereo, Sohms  2X600W
  • Performance Sensitivity (volts RMS) for full rated power at 8 ohms    0.775V
  • Frequency Response (at 1 watt,20Hz - 25kHz)    + OdB, -0.5dB
  • Phase Response (at 1 watt, 20Hzto20 kHz)    + 10' ,-20"
  • Signal to Noise Ratio below rated power A-weighted    >100dB
  • Total Harmonic Distortion (THD) at 1 full bandwidth power, from 20 Hz to 20 kHz    sSO.1%
  • Interrnodulation Distortion (IMD) 60 Hz and 7kHz at 4:1 .fromfull rated outputto -35 dB    sSO.05%
  • Damping Factor (8ohm): 20 Hzto 400 Hz    ^200
  • Input Impedance (nominallybalanced, nominally unbalanced)    20 kilohms, lOkilohms

 


Performance

  • Load Impedance (Note: Safe withall types ofloads)
  • 4-Channel Bridge-Stereo     4-8 ohms 8 ohms
  • AC Line Voltage and Frequency Configurations Available (+10%)         -220-240 V and50/60 Hz
  • AC Line Current (both amplifiers draw no more than 90 wattsat idle)      8A

    

Construstion

  • Ventilation                                Flow-through ventilation fromfront to back
  • Cooling                                    Proportional speed fan
  • Dimensions  H x W x D:             89mmX483mmx496mm
  • Net Weight/Shipping Weight       16kg/19kg

 

ŠALJEMO NA ADRESU!!!

Kratak opis Independent Bassand Treblecontrol for each channel. Three power configerations ; four channe!4 X 200W, 3 channel 2 X 200W + 1 X 600W or 2 channel 2X600W. Individual fourchannel inputs and switchable global bus input, independent volume control for 4 channels, recessed Treble and Bass control, Independent signal indication, independent clipindication. *Bridge modeswitch forchannel 1&2 andchannel 3&4, bridge and common protection LED indicators. •Balance BUS IN available.
499.00€
Martin Wisman ULG 320 (ULG 320)
Specifikacija

 

  • Stereo 4 ohm:  2x 170W
  • Stereo 8 ohm:  2x 100W
  • Stereo 2 ohm:  2x 200W
  • Bridge 8 ohm: 215W
  • Bridge 4 ohm: 400W
  • Frekvencijski odziv: 20 Hz a 20 kHz < +/- 0.5dB
  • Distorzija:   < 0.1 % (1 kHz)
  • Ulaz izolacija:  10 - 20 kohm balansirano
  • Signal / sum:   < 95 dB
  • Tezina:  7.5 kg
  • Napajanje:   230V / 50Hz
  • Dimenzije:   480 x 410 x 88 (19"/2U)


ŠALJEMO NA ADRESU!!!
Specifikacija Stereo 4 ohm: 2x 170W Stereo 8 ohm: 2x 100W Stereo 2 ohm: 2x 200W Bridge 8 ohm: 215W Bridge 4 ohm: 400W Frekvencijski odziv: 20 Hz a 20 kHz < +/- 0.5dB Distorzija: < 0.1 % (1 kHz) Ulaz izolacija: 10 - 20 kohm balansirano Signal / sum: < 95 dB Tezina: 7.5 kg Napajanje: 230V / 50Hz Dimenzije: 480 x 410 x 88 (19"/2U) ŠALJEMO NA ADRESU!!!
169.00€
Martin Wisman ULT 1260 (ULT 1260)
ULT 1260
 
 
Professional Power Amplifier
 
Soft start-up, preventing the transient surge and reducing the disturbance to the power network.
Working mode of Stereo, Bridge and Parallel can be chosen; the sensitivity of input signal  also can be chosen from 0.775V, 1.0V, 1.44V.
It use high speed& low noise, speed variable fans (the speed goes up along with the temperature increases); 
Limiter protection, overheat protection, over-current protection, DC protection and short circuit protection.
COMBO & XLR Link male input; SPEAKON and binding post output connectors.

Stereo 8Ω Power       420W x2
Stereo 4Ω Power       630W x2
Bridge 8Ω Power       1260W
THD+N                 ≤0.5%
IMD                   <0.3%
Frequency response     20Hz ~ 20kHz ± 1.5dB
Input Sensitivity          0.775V/1.0V/1.44V (stereo 8Ω)
S/N ratio                >100dB
Crosstalk                >70dB
Phase Response         ± 10 degrees
Damping Factor         >200 (@8Ω)
Protection    Soft start up, thermal cut off, short circuit, overloaded, DC fault, Voltage limiter and AC line fuse
Connectors              Input: COMBO x 2, XLR Link male x 2; Output: SPEAKON x 2; Binding Post x 2
Power supply            230V ± 10% ~50/60Hz
Dimension               483 x 345 x 88mm (19", 2U)
Weight                  18.5kgs
 
ŠALJEMO NA ADRESU!!!
ULT 1260 Professional Power Amplifier Soft start-up, preventing the transient surge and reducing the disturbance to the power network. Working mode of Stereo, Bridge and Parallel can be chosen; the sensitivity of input signal also can be chosen from 0.775V, 1.0V, 1.44V. It use high speed& low noise, speed variable fans (the speed goes up along with the temperature increases); Limiter protection, overheat protection, over-current protection, DC protection and short circuit protection. COMBO & XLR Link male input; SPEAKON and binding post output connectors. Stereo 8Ω Power 420W x2 Stereo 4Ω Power 630W x2 Bridge 8Ω Power 1260W THD+N ≤0.5% IMD <0.3% Frequency response 20Hz ~ 20kHz ± 1.5dB Input Sensitivity 0.775V/1.0V/1.44V (stereo 8Ω) S/N ratio >100dB Crosstalk >70dB Phase Response ± 10 degrees Damping Factor >200 (@8Ω) Protection Soft start up, thermal cut off, short circuit, overloaded, DC fault, Voltage limiter and AC line fuse Connectors Input: COMBO x 2, XLR Link male x 2; Output: SPEAKON x 2; Binding Post x 2 Power supply 230V ± 10% ~50/60Hz Dimension 483 x 345 x 88mm (19", 2U) Weight 18.5kgs ŠALJEMO NA ADRESU!!!
288.00€
QSC RMX 5050 (RMX 5050)
BROJ 1 U AMERICI, DALEKO ISPRED SVIH !!!
2 x 2500 W NA 2 OHM !!!


 
RMX 5050

SPECIFICATIONS
RMX 5050
     STEREO MODE, Both Channels Driven
8 ohms 
  FTC 20 Hz - 20 kHz, 0.1% THD
  EIA 1 kHz, 0.1% THD    
1050 W
1100 W
4 ohms
  FTC 20 Hz - 20 kHz, 0.1% THD
  EIA 1 kHz, 0.1% THD    
1600 W
1800 W
2 ohms 
  FTC 20 Hz-20 kHz 0.1% THD
  EIA 1 kHz 1% THD    
2000 W
2500 W
     BRIDGE-MONO MODE
8 ohms 
  FTC 20 Hz-20 kHz 0.1% THD
  EIA 1 kHz 0.1% THD    
3200 W
3600 W
4 ohms 
   EIA 1 kHz 1% THD    
5000 W
Distortion (SMPTE-IM)    Less than 0.02%
Distortion (Typical)
20 Hz - 20 kHz: 10 dB below rated power
1 kHz and below: full rated power    
Less than 0.02%
Less than 0.02%
Frequency Response

20 Hz - 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB
5 Hz - 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB
Damping Factor    Greater than 250 @ 8 ohm
Noise (unweighted)    100 dB below rated output (20 Hz - 20 kHz, 8 ohm load)
Input Sensitivity    1.42 Vrms for 1050 watts into 8 ohms
Voltage Gain    64x (36 dB) for 8 ohm load
Input Impedance    20k ohm balanced, 10k ohm unbalanced
Controls Front:
Controls Rear:

AC power switch, Ch. 1 and Ch. 2 gain control
10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel.
Indicators

Power-On: Green LED, Protect: Red LED
Signal -30dB: Yellow LED, Clip: Red LED
Connectors Input:
Connectors Output:    XLR female, TRS (1/4\"), and barrier-strip screw terminals, each channel
Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp)
Cooling    Continuously variable-speed fan, rear-to-front air flow
Amplifier Protection

Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads
Load Protection    On/off muting, DC fault output crowbar
Power Requirements    100, 120 or 240 Volts AC (±10%) 50-60 Hz (factory configured)
120V models require 20 Amp service and are supplied with a NEMA 5-20 plug on the cordset.
Dimensions    19\" (48.3 cm) wide, 5.25\" (13.3 cm) tall, 15.9\" (40.39 cm) overall depth
Weight    75 lbs (34.02 kg) net, 87 lbs (39.46 kg) shipping

ŠALJEMO NA ADRESU!!!
BROJ 1 U AMERICI, DALEKO ISPRED SVIH !!! 2 x 2500 W NA 2 OHM !!! RMX 5050 SPECIFICATIONS RMX 5050 STEREO MODE, Both Channels Driven 8 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 1050 W 1100 W 4 ohms FTC 20 Hz - 20 kHz, 0.1% THD EIA 1 kHz, 0.1% THD 1600 W 1800 W 2 ohms FTC 20 Hz-20 kHz 0.1% THD EIA 1 kHz 1% THD 2000 W 2500 W BRIDGE-MONO MODE 8 ohms FTC 20 Hz-20 kHz 0.1% THD EIA 1 kHz 0.1% THD 3200 W 3600 W 4 ohms EIA 1 kHz 1% THD 5000 W Distortion (SMPTE-IM) Less than 0.02% Distortion (Typical) 20 Hz - 20 kHz: 10 dB below rated power 1 kHz and below: full rated power Less than 0.02% Less than 0.02% Frequency Response 20 Hz - 20 kHz, 8 ohms, LF filter bypassed, +0/-1 dB 5 Hz - 50 kHz, 8 ohms, LF filter bypassed, +0/-3 dB Damping Factor Greater than 250 @ 8 ohm Noise (unweighted) 100 dB below rated output (20 Hz - 20 kHz, 8 ohm load) Input Sensitivity 1.42 Vrms for 1050 watts into 8 ohms Voltage Gain 64x (36 dB) for 8 ohm load Input Impedance 20k ohm balanced, 10k ohm unbalanced Controls Front: Controls Rear: AC power switch, Ch. 1 and Ch. 2 gain control 10-pole DIP switch featuring LF filter on/off, LF filter 30/50 Hz, Clip Limiter on/off controls for each channel and switches for selecting Stereo, Parallel, or Bridge mode. Push-button circuit breaker for each channel. Indicators Power-On: Green LED, Protect: Red LED Signal -30dB: Yellow LED, Clip: Red LED Connectors Input: Connectors Output: XLR female, TRS (1/4\"), and barrier-strip screw terminals, each channel Binding posts and Speakon® outputs (Ch. 1 Speakon wired for biamp) Cooling Continuously variable-speed fan, rear-to-front air flow Amplifier Protection Short circuit, open circuit, thermal, ultrasonic, and RF protection. Stable into reactive or mismatched loads Load Protection On/off muting, DC fault output crowbar Power Requirements 100, 120 or 240 Volts AC (±10%) 50-60 Hz (factory configured) 120V models require 20 Amp service and are supplied with a NEMA 5-20 plug on the cordset. Dimensions 19\" (48.3 cm) wide, 5.25\" (13.3 cm) tall, 15.9\" (40.39 cm) overall depth Weight 75 lbs (34.02 kg) net, 87 lbs (39.46 kg) shipping ŠALJEMO NA ADRESU!!!
1,867.00€
Per Page      1 - 16 of 16
  • 1